Redmax G3200 Manual de usuario

OWNER/OPERATOR MANUALCHAINSAWS848-C3A-93A0 (410)The engine exhaust from this productcontains chemicals known to the Stateof California to cause cancer

5. Installing guide bar and saw chain 10 While temporary tightening, you may hear the“click” sound. But do not stop tightening at thattime. This sou

6. Fuel and Chain oil 11  RECOMMENDED MIXING RATIOGASOLINE 50:OIL 1• Exhaust emission are controlled by thefundamental engine parameters andcompone

 12 6. Fuel and Chain oil CHAIN OIL Use motor oil SAE 10W-30 all year round, orSAE 30-40 in summer and SAE 20 in winter. Do not use waste or regene

It is very dangerous to run a chainsaw thatmounts broken parts or lacks any parts.Before starting engine, make sure that all theparts including bar an

 14 6. When engine has ignited, pull the throttle slightlyto return the choke knob to the original position.If the engine stops, pull the starter ag

1. H and L needles are restricted within the numberof turn as shown below. H needle –1/4 L needle –1/4 2. Start engine and allow it to warm up in

 16 7. OperationWhen the brake engages during operation,immediately release the throttle lever to stop theengine. STOPPING THE ENGINE 1. Release t

• Before proceeding to your job, read "ForSafe Operation" section It is recommendedto first practice sawing easy logs. This alsohelps you ge

 18  FELLING A TREE (F8-2) 1. Decide the felling direction considering thewind, lean of the tree, location of heavybranches, ease of job after fell

A Log lying on the ground (F8-3) Saw down halfway, then roll the log over and cutfrom the opposite side. A Log hanging off the ground (F8-4) In area A

 20 9. MaintenanceMaintenance, replacement, or repair of theemission control device and systems may beperformed by any non-road engine repairestabli

9. Maintenance4. Remove the cleaner element by unfastening thehooks. Split the element into halves and wash inneutral detergent and warm water. Afterc

 22 Be sure to block the air intake hole.2. Spark arresterThe muffler is equipped with a spark arrester toprevent red hot carbon from flying out of

SAW CHAIN It is very important for smooth and safeoperation to keep the cutters always sharp. Your cutters need to be sharpened when: • Sawdust beco

 24 10. Maintenance of Saw Chain and Guide Bar Make sure every cutter has the same length andedge angles as illustrated. (F10-3) (4) Cutter length (

11. Troubleshooting GuideCase 1. Starting failure: Make sure the icing prevention system is not working. Case 2. Lack of power/Poor acceleration/Rough

 26 1. Empty the fuel tank and run the engine out offuel. 2. Empty the oil tank. 3. Clean the entire unit. 4. Store the unit in a dry place out of t

 27 13. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/orreplacement. 2. KOMATSU ZENOAH does no

 28 G320013. Parts list Fig.1 POWER UNIT (S/N 404766 and up)

 29 G3200Fig.1 POWER UNIT (S/N 404766 and up)Key# PART NUMBER DESCRIPTIONQ'TY/UNITNOTE1 848-C30-12A1 CYLINDER 12 T2200-14210 GASKET, cyl 13 848

SAFETY FIRSTInstructions contained in warnings within thismanual marked with a symbol concerncritical points which must be taken intoconsideration to

G320013. Parts list Fig.2 POWER UNIT (S/N 404766 and up) 30 

G3200Fig.2 POWER UNIT (S/N 404766 and up) 31 Key# PART NUMBER DESCRIPTIONQ'TY/UNITNOTE1 848-C30-82H3 ROD 12 848-C30-82G2 GROMMET 13 848-C30-25A

 32 G3200EZ13. Parts list Fig.3 POWER UNIT (S/N 400001 and up)

 33 G3200EZFig.3 POWER UNIT (S/N 400001 and up)Key# PART NUMBER DESCRIPTIONQ'TY/UNITNOTE1 848-C30-12A1 CYLINDER 12 T2200-14210 GASKET, cyl 13 8

 34 G3200EZ13. Parts list Fig.4 POWER UNIT (S/N 400001 and up)

 35 G3200EZFig.4 POWER UNIT (S/N 400001 and up)Key# PART NUMBER DESCRIPTIONQ'TY/UNITNOTE1 848-C30-82H3 ROD 12 848-C30-82G2 GROMMET 13 848-C30-2

Key# PART NUMBER DESCRIPTIONQ'TY/UNITNOTE19 3310-81341 • VALVE 120 2880-81470 • SCREW 321 2670-81410 • SPRING 122 848-C3A-81T0 • SHAFT 123 2630-8

 37 G3200/G3200EZKey# PART NUMBER DESCRIPTIONQ'TY/UNITNOTE1 848-CB1-2020 BAR CV30 1/4 12 3310-52210-50 CHAIN OREGON 25AP-J68E 13 3617-97110 PRO

EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY, KOMATSU ZENOAHAMERICA INC. (THE COMPANY), THROUGH ANY RedMax DEALER, WIL

Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., parl'intermédiaire de n'importe quel revendeur

2. Specifications G3200 / G3200EZPower unit : Displacement ···················································································· 2.00(

KOMATSU ZENOAH AMERICA INC.4344 Shackleford Road Suite 500Norcross, Georgia 30093

3. Symbols on the machine 5 Made in JapanRedMax IMPORTANT ENGINE INFORMATION THIS ENGINE CONFORMS TO US EPA PH1 FOR SMALL OFF-ROAD ENGINES.

 6 4. For safe operation1. Never operate a chain saw when you arefatigued, ill, or upset, or under theinfluence of medication that may makeyou drows

 7 4. For safe operation17. Operate the chain saw only in wellventilated areas. Never start or run theengine inside a closed room or building.Exhaus

A standard saw unit package contains the items asillustrated. (1) Power unit (2) Bar protector (3) Guide bar(4) Saw chain (5) Plug wrenchOpen the box

5. Installing guide bar and saw chain 9 A new chain will expand its length in the beginningof use. Check and readjust the tension frequentlyas a loo